Showing 1–16 of 45 results
This leather gaiter fits all cars built after the squarer late tunnel without the MKI starter housing (introduced during 1973). It is retained by a metal ring which is screwed into the transmission tunnel after first passing it through the cutaway in the carpet. This will not fit either Mini vans or pickups built before…
This gaiter fits all cars built after the squarer late tunnel without the MKI starter housing (introduced during 1973). It is retained by a metal ring which is screwed into the transmission tunnel after first passing it through the cutaway in the carpet. This will not fit either Mini vans or pickups built before 1976…
This wire squab diaphragm will fit all Minis built between 1960 and 1993 (before the twin post headrest seats were introduced). Originally the early Minis used a one piece moulded rubber diaphragm, however these are no longer available. The wire diaphragm superseded the rubber version item and can be used for a direct swap for…
This is the top of the range, heavy duty spray glue that we use in our factory to make all our trim products on a day to day basis. We recommend you use spray glue to fit your Newton products to your car. Its a full 500ml can, wrapped in bubble wrap for safe transport….
An ingenious solution to the modern bracket that stops the doors from opening too far, these straps are made from vinyl with a strong nylon fabric sewn inside. They attach to the front of the door and the rear edge of the A panel, about level with the top of the storage bins. The metal…
This original design lamp cover is suitable for both the original Lucas lamps of the 1950 s and 60 s but also all other circular six inch lamps fitted to the classic Minis. There are two designs available, the Q style lamp cover pictured here and the Lion style, both of which incorporate the small clear window…
This original design lamp cover is suitable for both the original Lucas lamps of the 1950 s and 60 s but also all other circular six inch lamps fitted to the classic Minis. There are two designs available, the Q style lamp cover pictured here and the Lion style, both of which incorporate the small…
This original design lamp cover is suitable for both the original Lucas lamps of the 1950 s and 60 s but also all other circular seven inch lamps fitted to the classic Minis. There are two designs available, the Q style lamp cover pictured here and the Lion style, both of which incorporate the small clear window…
Made from a heavy duty carpet backed with a non slip rubber backing, these carpets sit on top of the main carpet set to protect from wear. These will fit any Mini built after 1973 when the square straight tunnel was introduced. As standard the mats our bound in a matching binding although a range of…
Made from a heavy duty carpet backed with a non slip rubber backing, these carpets sit on top of the main carpet set to protect from wear. These will fit any Mini built before 1973 with the original floor mounted start button and have the relevant cut out to clear this. As standard the mats our…
This length of black leathercloth is sufficient to cover the internal A-posts, dash top rail and dash lower rail on any Mini with a centre speedometer, lacking the moulded plastic fascia introduced on the Clubman. These areas were always originally covered on the original Coopers, otherwise on standard cars they were normally visible as bare painted…
This strong felt backed PVC material will help with noise reduction. Glued to the front bulkhead under the bonnet, you may need to cut some holes or slit the material to fit this around various mechanicals, depending on the exact specification of your Mini.Â
We offer a seat fitting service for those who would prefer their seats to turn up ready to fit directly into the car. Our professional seat fitters will strip down your original seat, removing your old worn seat covers, foams and diaphragms, sandblast and repaint the seat frame and fit with brand new covers. Please note…
This jack bag will hold the original style scissor jack & lever and is bound with the tie straps. The bag is slightly smaller with a deeper pocket than our part number CK721 which uses a bigger jack that we believe was used on models after the MKIII models. The bag is made of very hard-wearing material…
This jack bag will hold the jack & lever and is bound with the tie straps. The bag is made of very hard-wearing material and will last many years. This bag is made out of Hardura which is a heavy PVC with a felt backing moulded to it which is very hard wearing.
This leather gaiter fits all MKI, MKII and early MKIII cars built with the early tunnel arrangement, but fitted with the remote control gear change (i.e. not Magic Wand ) which brought the gear knob in much easier reach of the driver and made for a faster gear change. This was first seen on the…
End of content
End of content
No products in the cart.
