Showing 1–16 of 156 results
In the early years of production manufacture was shared between two factories. While mechanically the same, the Austin Seven and Morris Mini used their own trim designs and these designs varied throughout these years until trim became more standardised after 1962. This design was used exclusively in early Morris production, and fits the post leg…
In the early years of production manufacture was shared between two factories. While mechanically the same, the Austin Seven and Morris Mini used their own trim designs and these designs varied throughout these years until trim became more standardised after 1962. This design was used exclusively in early Morris production. We believe that this trim was…
This leather gaiter fits all cars built after the squarer late tunnel without the MKI starter housing (introduced during 1973). It is retained by a metal ring which is screwed into the transmission tunnel after first passing it through the cutaway in the carpet. This will not fit either Mini vans or pickups built before…
This gaiter fits all cars built after the squarer late tunnel without the MKI starter housing (introduced during 1973). It is retained by a metal ring which is screwed into the transmission tunnel after first passing it through the cutaway in the carpet. This will not fit either Mini vans or pickups built before 1976…
This Classic Mini 9-piece loop pile moulded carpet set is designed to fit the 1973 onwards model of Mini which features the later style square front tunnel. Our loop pile Mini carpet is an alternative to our standard nylon based carvel material and is available in black, brown or grey. The kit contains the front (moulded)…
This moulded carpet kit will fit any Mini saloon built with the late ‘square’ front tunnel, which was introduced in 1973. The previous tunnel design was much more rounded and included the hump for the MKI starter housing, which by 1973 had long been redundant on most models. The kit contains the front (moulded) and rear…
When refurbishing your seats we recommend the fitting of new foams and diaphragms to give the best possible fit for new seat covers. These foams were used exclusively on Minis built between 1985 and 1992 before the introduction of moulded seat foams. The foam is much more shaped than earlier foams and as you can…
When refurbishing your seats we recommend the fitting of new foams and diaphragms to give the best possible fit for new seat covers. These foams were used exclusively on Minis built between 1985 and 1992 before the introduction of moulded seat foams. The foam is much more shaped than earlier foams and provides more support…
All Mini front seats were upgraded in 1993 with new seat frames and foam cushions with more pronounced side bolsters to give a much more comfortable and safer ride. As can be seen here the side bolsters on both base and squab are very modern compared to the earlier seating options that were very flat. …
All Mini front seats were upgraded in 1993 with new seat frames and foam cushions with more pronounced side bolsters to give a much more comfortable and safer ride. As can be seen here the side bolsters on both base and squab are very modern compared to the earlier seating options that were very flat….
This pair of C-posts are specially shaped to fill the pillars on the Iate 1996 Mini onwards with the introduction of the seatbelt mountings into this area. Included in the kit is a strip of spare material to cover the exposed body between the rear window rubber and the parcel shelf. As with the originals…
These metal stays are inserted into the headlining canopy for headlinings built after 1970. The stays are supplied colour coded and we provide instructions to guide you through their fitting. Â Newton Commercial Part No – HL3030 View fitting instructions
In the early years of production manufacture was shared between two factories. While mechanically the same, the Austin Seven and Morris Mini used their own trim designs and these designs varied throughout these years until trim became more standardised after 1962. This design was used exclusively in Austin production and matches the seat covers with…
 In the early years of production manufacture was shared between two factories. While mechanically the same, the Austin Seven and Morris Mini used their own trim designs and these designs varied throughout these years until trim became more standardised after 1962. This design was used exclusively in Austin production and matches the seat covers with…
This strap is designed to fit alongside the Mini battery cover and hold this in place. Please note that these will only fit Minis fitted with the original standard size battery. Newton Commercial Part No – PT3011
This kit comes with both the bonnet and bulkhead insulation pieces. This strong felt backed PVC material will help with noise reduction. The main bonnet felt pad is supplied bound and quilted and will need to be glued to the bonnet with the supplied high temperature glue. The bulkhead piece will need to be glued…
End of content
End of content
No products in the cart.
