Showing 1–16 of 92 results
Some customers do not like the bare-painted boot area. We have developed a carpet kit that covers the entire inside which makes it look good and also acts as a sound-deadening kit. The kit contains a hardboard bulkhead panel covered in carpet, and a pair of boards again covered in carpet which fit over the…
Some customers do not like the bare painted boot area. We have developd a carpet kit which covers the entire inside which makes it looks good and also acts as a sound deadening kit. The kit contains a hardboard bulkhead panel covered in carpet, a pair of boards again covered in carpet which fit over…
This plain covererd visor fits all models of Spitfire and GT6 on either RHD or LHD cars. Only available in Black.
This panel is made of Bitumen board which is waterproof. The board is stamped out on our 60 Ton press and the two sides have black metal strenghening strips applied. Each board comes with three brackets to attach it to the vehicle. Small nuts and bolts are not supplied. Newton Commercial Part No – EV1646Â
This passenger side glove box is of a black fabricated painted and grained fibreboard construction to original Triumph specification. It will fit Mk.1-2 & 3 Spitfire models but only the GT6 mk.1 cars. Various punched holes are for attachment to the dash area.
This product looks fairly simple, but the metal part is a stamped out mild steel piece with a hard spunge rubber glued to the outer surface to help your legs in the event of a crash!. All this is covered in black vinyl material. This item supports the lower leading edge of your glove box.
The headlining material we use is actually called Longhorn design because of the very heavy graining in the material. This material was originally used by the factory. All necessary sewn hoops are stitched in place to accept the roof stays. Newton Commercial Part No – HL1640
This is a replacement headrest cover. The bottom of your headrest has a plastic plate which can be unscrewed which will then show staples which hold the cover in place. Remove the cover. Turn your new cover inside out and slowly slide it over the foam turning it the right way. Check before stapling that…
This is a replacement headrest cover. The bottom of your headrest has a plastic plate which can be unscrewed which will then show staples which hold the cover in place. Remove the cover. Turn your new cover inside out and slowly slide it over the foam turning it the right way. Check before stapling that…
This is a replacement headrest cover. The bottom of your headrest has a plastic plate which can be unscrewed which will then show staples which hold the cover in place. Remove the cover. Turn your new cover inside out and slowly slide it over the foam turning it the right way. Check before stapling that…
This is the top of the range, heavy duty spray glue that we use in our factory to make all our trim products on a day to day basis. We recommend you use spray glue to fit your Newton products to your car (where applicable). You will mainly use this product to fit underfelt and…
The dashboard support bracket can be covered in this piece of stretchy vinyl.
Our door panels are exact replicas of the Factory originals. The panels are die cut on our 60 ton presses and have all the correct holes and apertures for the perfect fit. As can be seen the design of the weld lines looks very effective. The carpet kick panels are firstly sewn to a vinyl…
Our door panels are exact replicas of the Factory originals. The panels are die cut on our 60 ton presses and have all the correct holes and apertures for the perfect fit. The carpet kick panels are firstly sewn to a vinyl surround, which in turn is welded to the face panel on our High…
Our door panels are exact replicas of the Factory originals. The material on this model had a courser grained vinyl finish than earlier models.(Known as \1290\ grain in the Trade) The panels are die cut on our 60 ton presses and have all the correct holes and apertures for the perfect fit. The carpet kick…
We were asked by a top restorer of classic cars to design an Inner door liner to stop water regress onto new or old door cards fitted. Most enthusiast would use the plastic bag the panels came in and hope it would stick to the door with glue they had in the garage! Our range…
End of content
End of content
No products in the cart.
